Code: Select all
gitgit clone https://github.com/cmbant/CosmoMC.git
But I set checkpoint to T(true) in test.ini because I want to check if I can stop the program and then resume.When I run
Code: Select all
mpirun -np 2 ./cosmomc test.ini
Code: Select all
mpirun -np 2 ./cosmomc test.ini
Code: Select all
Number of MPI processes: 2
file_root:test
Random seeds: 7944, 16851 rand_inst: 1
Random seeds: 8044, 16851 rand_inst: 2
Using clik with likelihood file ./data/clik/hi_l/plik/plik_dx11dr2_HM_v18_TT.clik
----
clik version 723c1a4b0580
smica
----
clik version 723c1a4b0580
smica
Checking likelihood './data/clik/hi_l/plik/plik_dx11dr2_HM_v18_TT.clik' on test data. got -380.979 expected -380.979 (diff -8.6809e-09)
----
TT from l=0 to l= 2508
Checking likelihood './data/clik/hi_l/plik/plik_dx11dr2_HM_v18_TT.clik' on test data. got -380.979 expected -380.979 (diff -8.6809e-09)
----
TT from l=0 to l= 2508
Clik will run with the following nuisance parameters:
A_cib_217
cib_index
xi_sz_cib
A_sz
ps_A_100_100
ps_A_143_143
ps_A_143_217
ps_A_217_217
ksz_norm
gal545_A_100
gal545_A_143
gal545_A_143_217
gal545_A_217
calib_100T
calib_217T
A_planck
Using clik with likelihood file ./data/clik/low_l/commander/commander_rc2_v1.1_l2_29_B.clik
----
clik version 723c1a4b0580
gibbs_gauss 1478fb2d-28fa-49ac-a8ae-677dbdc3600a
Checking likelihood './data/clik/low_l/commander/commander_rc2_v1.1_l2_29_B.clik' on test data. got -7.32304 expected -7.32304 (diff -2.52096e-10)
----
TT from l=0 to l= 29
Clik will run with the following nuisance parameters:
A_planck
----
clik version 723c1a4b0580
gibbs_gauss 1478fb2d-28fa-49ac-a8ae-677dbdc3600a
Doing non-linear Pk: F
Doing CMB lensing: T
Doing non-linear lensing: T
TT lmax = 2508
EE lmax = 2500
ET lmax = 2500
BB lmax = 2500
PP lmax = 2500
lmax_computed_cl = 2508
Computing tensors: F
max_eta_k = 14000.0000
transfer kmax = 5.00000000
Checking likelihood './data/clik/low_l/commander/commander_rc2_v1.1_l2_29_B.clik' on test data. got -7.32304 expected -7.32304 (diff -2.52096e-10)
----
TT from l=0 to l= 29
adding parameters for: smicadx12_Dec5_ftl_mv2_ndclpp_p_teb_consext8
adding parameters for: commander_rc2_v1.1_l2_29_B
adding parameters for: BK14_dust
adding parameters for: plik_dx11dr2_HM_v18_TT
Fast divided into 2 blocks
Block breaks at: 15
28 parameters ( 7 slow ( 0 semi-slow), 21 fast ( 0 semi-fast))
2 Reading checkpoint from chains/test_2.chk
1 Reading checkpoint from chains/test_1.chk
starting Monte-Carlo
Chain 2 MPI communicating
TRealArrayList: object of wrong type
Note: The following floating-point exceptions are signalling: IEEE_INVALID_FLAG IEEE_UNDERFLOW_FLAG
--------------------------------------------------------------------------
mpirun has exited due to process rank 1 with PID 0 on
node narip-pc exiting improperly. There are three reasons this could occur:
1. this process did not call "init" before exiting, but others in
the job did. This can cause a job to hang indefinitely while it waits
for all processes to call "init". By rule, if one process calls "init",
then ALL processes must call "init" prior to termination.
2. this process called "init", but exited without calling "finalize".
By rule, all processes that call "init" MUST call "finalize" prior to
exiting or it will be considered an "abnormal termination"
3. this process called "MPI_Abort" or "orte_abort" and the mca parameter
orte_create_session_dirs is set to false. In this case, the run-time cannot
detect that the abort call was an abnormal termination. Hence, the only
error message you will receive is this one.
This may have caused other processes in the application to be
terminated by signals sent by mpirun (as reported here).
You can avoid this message by specifying -quiet on the mpirun command line.
Code: Select all
mpirun -quiet -np 2 ./cosmomc test.ini